Setting up the Testing Environment

When running tests with Network Virtualization, the traffic of the Application Under Test (AUT) must flow through NV Test Manager.

To enable the required flow of network traffic, select one of the available configuration options, according to your needs.

For assistance in setting up the environment, contact your HPE Software representative.

Configuration 1: Set up NV as a desktop client

In this configuration, NV Test Manager is installed on each testing client. This may be significant when testing a web browser or thick client program running on Windows or Linux. If the AUT cannot operate locally on the same client as NV Test Manager, then an alternative configuration must be used. This may occur when testing mobile apps or where the AUT does not operate on a supported Windows or Linux platform.

To set up NV as a desktop client

  1. Install NV Test Manager on each client. For details, see Before You Install.

    If your application uses HTTPS, do one of the following:

    • During installation, enable the NV Proxy.
    • After installation, enable the NV Proxy in the NV Test Manager Settings.
  2. Install the NV proxy certificate.

  3. Configure the client to use the NV proxy.

  4. Configure the upstream proxy.

    Required when the application server is behind a proxy, for example, when the application server is on the cloud, and NV Test Manager is on the LAN behind the corporate proxy.

    1. Open NV Test Manager and select Settings.

    2. Configure the upstream proxy address and port.

Back to top

Configuration 2: Set up NV as a proxy

In this configuration, NV Test Manager is installed on a single machine in the testing lab with its proxy enabled. The clients are configured to use the NV proxy. When the AUT traffic flows through the NV Test Manager, the specified real world network conditions are emulated.

This configuration supports testing applications where the client cannot operate on the same platform as NV Test Manager. This may occur with on-device testing of mobile and mobile-web applications or desktop testing of web applications. This is the preferred method for on-device mobile testing.

Note:  

  • Make sure that Client Isolation is disabled on the wireless router. The wireless network must allow devices to use another device on the network as a proxy. In this case, the test devices use the NV Test Manager workstation as a proxy.

  • Make sure that no Network Address Translation (NAT) device is placed between the clients and the NV Test Manager host machine.

  • If a proxy is configured on a mobile device, mobile web applications always use that proxy because they run in a browser. Native applications, however, might ignore the device's proxy settings.

To set up NV as a proxy:

  1. Install NV Test Manager.

    For details, see Before You Install. During installation, make sure to enable the NV Proxy if the AUT uses HTTPS or is a mobile application. Alternatively, you can enable the proxy in the Settings tab of the Test Manager.

    Note: Some test devices may fail to reach the proxy when using the proxy's host name. Therefore, we recommend that you assign a static IP address to the NV Test Manager machine and use the assigned address when configuring the test devices with the proxy.

  2. Install the proxy’s SSL certificate on the client testing devices.

    This enables the AUT to communicate through the proxy.

    1. Connect the device to the wireless network.

    2. Make sure that the proxy is configured on the device. See Configuring the test devices to use the proxy server for details. 

    3. Browse to: <http/https>://<NV Test Manager address>:<NV Test Manager port; 8182 by default>/hpenv.cer

    4. Download and install the certificate.

      • On Windows, install the certificate to the Trusted Root Certification Authorities store.

      • On iOS 10.3 and later, browse to Settings > General > About > Certificate Trust Settings, and enable full trust for the certificate. For more details, see https://support.apple.com/en-il/HT204477.

      Alternatively, install your company's self-signed certificate.

  3. Configure the client test devices to use the proxy server:

  4. Verify that each client test device communicate successfully through the proxy.

    1. From Test Manager, start a Quick Test. In both the Include section of Client IPs and the Exclude section of Server IPs, select the IP of the device configured to use the proxy.

    2. On the device, browse to a website. Verify a website that uses HTTPS, if needed.

    3. In Test Manager, switch to the Statistics tab and make sure that the throughput is not 0.

Back to top

See also: